View APAXT10C1_4100841.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

w
w
a D . w
aS t
LCD MODULE SPECIFICATION
ee h
4U t
om .c
Products Name:APAX T10C1 10.4 INCH (800x600) COLOR TFT LCD MODULE 3.3V
l Preliminary Specification
This technical specification is tentative and it will be changed without notice.
w
w
w
t a .D
S a
e h
U t4 e
.c
m o
i/Ie*~N/|--1/2q
x _ o I * c u76 N 39 4 1/4O o Tel:0 2-87912868 Fax:02-87912869 Version. 1.0
w
w
w
.D
a
aS t
ee h
4U t
om .c
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
CONTENTS REVISION HISTORY GENERAL DESCRIPTION 1. ABSOLUTE MAXIMUM RATINGS 1.1 ABSOLUTE RATINGS OF ENVIRONMENT 1.2 ELECTRICAL ABSOLUTE RATINGS 2. ELECTRICAL SPECIFICATIONS 2.1 TFT LCD MODULE 2.2 BACKLIGHT UNIT 3. BLOCK DIAGRAM 3.1 TFT LCD MODULE 3.2 BACKLIGHT UNIT 4. INTERFACE SPECIFICATIONS 4.1 THE PIN ASSIGNMENT OF LVDS INTERFACE CONNECTOR 4.2 INPUT SIGNAL TIMING SPECIFICATIONS 4.3 COLOR DATA INPUT ASSIGNMENT 4.4 POWER UP/DOWN SEQUENCE 5. OPTICAL CHARACTERISTICS 5.1 TEST CONDITIONS 5.2 OPTICAL SPECIFICATIONS 6. MECHANICAL DRAWING 7. PRECAUTION 7.1 ASSEMBLY AND HANDLING PRECAUTION 7.2 SAFETY PRECAUTION
2/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
REVISION HISTORY
Version Ver 0.0 Ver 0.1 Date Description Aug. 29, '00 Tentative Specification was First Issued for CMO internal use only. Oct. 16, `00 1. All new specification formats. 2. Changing module outline dimensions & bezel opening area from 224.5x173.4mm and 214.4x162.0mm to 224.5x172.0mm and 214.2x161.8mm on page 4/19 and attached drawings. 3. Fixed interface connector P/N: DF19KR-20P-1H (Hirose) on page 9/19 and attached drawings. 4. Interface pin assignment: Pin 17 to Pin 20 connect to ground on page 9/19. 5. Adding input signal timing specifications on pages 10/19 and 11/19.
3/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
GENERAL DESCRIPTION OVERVIEW
This product is a 10.4" TFT Liquid Crystal Display Module with 1 edge CCFL Backlight unit and 20 pins LVDS interface. This module supports 800 x 600 SVGA mode and can display 262,144 colors. The inverter module for Backlight is not built in.
FEATURES
-SVGA (800x600 pixels) resolution -1 edge CCFL (Cold Cathode Fluorescent Lamp) -Standard Mode -LVDS (Low Voltage Differential Signaling) Interface
APPLICATION
-IA (Information Appliance) & TFT-LCD Notebook PC
GENERAL SPECIFICATI0NS
Item Screen Size Bezel Opening Area Effective Display Area Driver Element Pixel Number Pixel Pitch Pixel Arrangement Display Colors Transmissive Mode Surface Treatment Spec. 10.4 Diagonal 214.2(H)X161.8(V) 211.2(H)x158.4(V) a-si TFT active matrix 800xR.G.B.x600 0.264(H)x0.264(W) RGB vertical stripe 6 bits, 262,144 Normally White Haze 12Hard-Coating, Anti-static Unit inch mm mm pixel mm color -
MECHANICAL SPECIFICATIONS
Item Horizontal(H) Module Size Vertical(V) Depth(D) Weight Min. (224.0) (171.5) Typ. 224.5 172.0 (5.7) Max. (225.0) (172.5) 6 (310) Unit mm mm mm g Note
4/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
1. ABSOLUTE MAXIMUM RATINGS 1.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item Storage temperature Operating temperature (Ambient Temperature) Shock(non-operating) Vibration(non-operating) 90% RH Max. (Ta 40C). Maximum wet-bulb temperature at 39C or less. (Ta > 40C) No condensation. Note (2) 11ms, half-sine wave, three times for X, Y, Z. Note (3) 10-500 Hz, 30min/cycle, for X, Y, Z direction, each 2 Hrs. Note (4) At testing Vibration and Shock, the fixture in holding the Module to be tested has to be hard and rigid enough so that the Module would not be twisted or bent by the fixture. Symbol Tst Top Snop Vnop Values Min. -20 0 Max. +60 +50 50 1.5 Unit C C G G Note (1) (1) (2),(4) (3),(4)
Note (1) Temperature and relative humidity range is shown in the figure below.
Relative Humidity (%RH)
100 90 80 60
Operating Range
40 20 5 -40 -20 0
Storage Range
20 40 60 80
Temperature (C)
1.2 ELECTRICAL ABSOLUTE RATINGS (1) TFT LCD MODULE
Item Power Supply Voltage Logic Input Voltage Symbol Vcc VIN Values Min. Vss - 0.3 Vss - 0.3 Max. + 4.0 Vcc + 0.3 Unit V V Note Ta = 25 2 C
5/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
(2) BACKLIGHT UNIT
Item Lamp Current Lamp Frequency Symbol IL FL Value Min. Max. 6.0 80 Unit mARMS KHz Note (1),(2) (1)
Note (1) Permanent damage to device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for lamp (Refer to 2.2 for further information).
2. ELECTRICAL SPECIFICATIONS 2.1 TFT LCD MODULE
MODULE Parameter Power Supply Voltage Power Supply Current Ripple Voltage Differential Input Voltage for LVDS Receiver Threshold Rush Current pattern. Note (2) Measurement Conditions
+3.3V Q1 2SK1475 FUSE R1 47K (High to Low) (Control Signal) SW 1K +12V VR1 C1 1uF 47K C2 0.01uF C3 1uF VCC (LCD Module Input)
Symbol VCC l CC Vrp VIH VIL Irush
High Low
Min. (3.0) -100 -
Value Typ. (3.3) TBD (100) -
Max. (3.6) TBD +100 TBD
Unit V mA mV V V A
Note (1) (2)
Note (1) Operating Temp. range is 0 ~ 50 C, and the value of power supply current is measured in black
R2
Q2 2SK1470
VCC rising time is 470us
+3.3V
0.9VCC 0.1VCC
GND 470us
6/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
2.2 BACKLIGHT UNIT
Parameter Lamp Input Voltage Lamp Current Lamp Turn On Voltage Operating Frequency Lamp Life Time Power Consumption Symbol VL IL VS FL LBL PL BACKLIGHT ( one CCFL) Value Min. Typ. Max. (510) (560) (610) (2.0) (4.3) (6.0) o (800)(25 C) o (1050)(0 C) (40) (55) (80) 10,000 (25,000) (2.4) Unit VRMS mARMS VRMS VRMS KHz Hrs W Note IL=4.3mA (1) (2) (2) (3) (5) (4), IL=4.3mA
Note (1) Lamp current is measured by utilizing a current meter for high frequency as shown below: Hot(White) 1 2 GND(Black) A
LCD Module
Inverter
(Equipment Model: Y2016)
Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup. Otherwise the lamp may not be turned on. Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the display, and this may cause line flow on the display. In order to avoid interference the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible. Note (4) PL = ILxVL. Note (5) The lifetime (Hr) of a lamp can be defined as the time in which it continues to operate under the condition Ta = 252 and IL = 5.0 mArms until one of the following event occurs: (a) When the brightness becomes 50% or lower than its original, (b) When the effective ignition length becomes 80% or lowers than its original value. (Effective ignition length is defined as an area that has less than 70% brightness compared to the brightness in the center point.) Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. The performance of the backlight, such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for the lamp. All the parameters of an inverter should be designed with care so as not to produce too much current leakage from high-voltage output of the inverter. When designing or ordering the inverter please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When the above situation is confirmed, the module should be operated in the same manners as it is installed in your instrument.
7/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
The connector information of Blacklight unit. Pin 1 2 Symbol HV LV Description High Voltage Ground Remark White Black
Note (1) Connector Part No.: BHSR-02VS-1 (JST) Note (2) User's connector Part No.: SM02B-BHSS-1-TB (JST)
3. BLOCK DIAGRAM 3.1 TFT LCD MODULE
Rxin0(+/-)
Rxin1(+/-) Rxin2(+/-) CLK(+/-) Vcc Vcc GND
LVDS INPUT / TIMING CONTROLLER ASIC
SCAN DRIVER IC
TFT-LCD PANEL (800x3x600)
INPUT CONNECTOR (DF19KR-20P-1H)
DATA DRIVER IC DC/DC CONVERTER & REFERENCE VOLTAGE GENERATOR
VL
LAMP CONNECTOR (JST-BHSR-02VS-1)
BACKLIGHT UNIT
3.2 BACKLIGHT UNIT
1 2
Hot Cold
8/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
4. INTERFACE SPECIFICATIONS 4.1 THE PIN ASSIGNMENT OF LVDS INTERFACE CONNECTOR
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VCC VCC Vss Vss Rxin0Rxin0+ Vss Rxin1Rxin1+ Vss Rxin2Rxin2+ Vss CLKCLK+ Vss GND GND GND GND Description Power supply +3.3 v Power supply +3.3 v Ground Ground LVDS differential data input (Negative) LVDS differential data input (Positive) Ground LVDS differential data input (Negative) LVDS differential data input (Positive) Ground LVDS differential data input (Negative) LVDS differential data input (Positive) Ground LVDS Clock Data input (Negative) LVDS Clock Data input (Positive) Ground Ground Ground Ground Ground Notes R0~R5,G0 G1~G5,B0,B1 B2~B5,DE,Hsync, Vsync LVDS level -
Note (1) Connector Part No.: DF19KR-20P-1H (Hirose) or equivalent Note (2) User's connector Part No: DF19G-20S-1C (Wire), DF19G-20S-1F-GND (FPC) or DF19G-20S-1SD-GND (Co-Axial cable)
9/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
4.2 INPUT SIGNAL TIMING SPECIFICATIONS
The specifications of input signal timing are as the following table and timing diagram. Signal Parameter Symbol Min Typ Max Unit DCLK Pixel clock period Tck 25 ns Duty ratio (%Tch) TBD 50 TBD % Rise time Trck TBD TBD ns Fall time Tfck TBD TBD ns DATA Setup time Tsd TBD TBD ns Hold time Thd TBD TBD ns Rise time Trd TBD ns Fall time Tfd TBD ns DE Setup time Tsde TBD TBD ns Hold time Thde TBD TBD ns VSYNC Vertical period Tvp TBD 628 TBD Thp Vertical display blank period Tvdb TBD 28 TBD Thp Vertical display active period Tvda 600 600 600 Thp Vertical sync. back porch Vbp TBD 23 TBD Thp Vertical sync. front porch Vfp TBD TBD TBD Thp Vertical sync. pulse width Vpw TBD 4 TBD Thp HSYNC Horizontal period Thp TBD 1056 TBD Tck Horizontal display blank period Thdb TBD 256 TBD Tck Horizontal display active Thda 800 800 800 Tck period Horizontal sync. back porch Hbp TBD 88 TBD Tck Horizontal sync. front porch Hfb TBD TBD TBD Tck Horizontal sync. pulse width Hpw TBD 128 TBD Tck Remarks Tch/Tck
10/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
INPUT SIGNAL TIMING DIAGRAM
Vpw VSYNC Vbp Tvp Tvdb HSYNC Tvda Vfp
DE
600
1
2
600
Hpw HSYNC Hbp Thp Thdb DE DCLK Thda Hfp
DATA
Valid display data (800 Tck)
Invalid
Valid
Tck Tch
90% 50%
Trck
Tfck
DCLK Tsd DATA Thd
10%
90% 50% 10%
Trd / Tfd Thde Tsde
DE 11/19
50%
This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
4.3 COLOR DATA INPUT ASSIGNMENT
Data Signal Green
R1 R0 G5 G4 G3 G2 G1 G0 B5 B4
Color
R5 R4
Red
R3 R2
Blue
B3 B2 B1 B0
Basic Colors
Gray Scale Of Red
Black Red Green Blue Cyan Magenta Yellow White Red(0) / Dark Red(1) Red(2) : : Red(61) Red(62) Red(63) Green(0) / Dark Green(1) Green(2) : : Green(61) Green(62) Green(63) Blue(0) / Dark Blue(1) Blue(2) : : Blue(61) Blue(62) Blue(63)
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 1 0 0 0 1 1 1 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0
0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1
0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1
Gray Scale Of Green
Gray Scale Of Blue
12/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
4.4 POWER UP/DOWN SEQUENCE
t4
Vcc
0V
90% 10% t1
90% 10% t3 10%
Signals
0V
t2
t5
t6
CCFL
Timing Specifications: 0 t1 TBD 0 t2 TBD 0 t3 TBD t4 TBD t5 TBD t6 TBD Notes: (1) Please avoid floating state of interface signal at invalid period. (2) When the interface signal is invalid, be sure to pull down the power supply for LCD Vcc to 0V.
13/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
5. OPTICAL CHARACTERISTICS 5.1 TEST CONDITIONS
Item Ambient Temperature Ambient Humidity Supply Voltage Input Signal Inverter Current Inverter Driving Frequency Inverter Symbol Value Unit o Ta C 252 Ha %RH 5010 VCC 3.3 V According to typical value in "Electrical Characteristics" IL 4.3 mA FL (55) K Hz TBD
The measuring method is shown in 5.2. The following items are measured under stable conditions about 20 minutes after the module works. The optical characteristics should be measured under lamp current IL = 6.0 mArms and in a dark environment ( 2 lux) or equivalent state with the methods shown in Note (6).
5.2 OPTICAL SPECIFICATIONS
Item Contrast Ratio Response Time Average Luminance of White White Variation Red Green Blue White Horizontal Viewing Angle Vertical
Symbol
Conditions
CR TR TF LAVE W Rx Ry Gx Gy Bx By Wx Wy x+ xY+ YCR10 x=0, Y =0 Viewing Normal Angle
Min. (150) TBD -
Typ. (200) (15) (35) (150) (1.4) TBD TBD TBD TBD TBD TBD (0.31) (0.33)
Max. (30) (50) (1.6)
Unit Note (2),(5) ms (3) ms 2 cd/m (4),(5) (5),(6)
Color Chromaticity
Deg.
(1),(5)
(40) (40) (10) (30)
(45) (45) (15) (35)
14/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
Note (1) Definition of Viewing Angle (x, y): Normal x = y = 0 yX- = 90 xx- x+ y+ 12 o'clock direction y+ y+ = 90
6 o'clock y- = 90
y-
x+
X+ = 90
Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63 L 0: Luminance of gray level 0 CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
Note (3) Definition of Response Time (TR, TF):
Gray Level 63
100% 90%
Gray Level 63
Optical Response Gray Level 0
10% 0%
Time TR TF
15/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
Note (4) Definition of Average Luminance of White (LAVE): Measure the luminance of gray level 63 at 5 points LAVE = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5 L (x) is corresponding to the luminance of the point X at Figure in Note (6).
Note (5) Measurement Set-Up: The LCD module should be stabilized at a given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room.
LCD Module LCD Panel Center of the Screen Photometer (TOPCON BM-5A)
Field of View = 2
Light Shield Room (Ambient Luminance < 2 lux)
500 mm
Note (6) Definition of White Variation (W): Measure the luminance of gray level 63 at 5 points W = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]
Horizontal Line D
D/4 D/2 3D/4
Vertical Line
W/4
1 5
2 X
W
W/2
: Test Point X=1 to 5
3W/4
3
4
Active Area 16/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
Issue Date: Oct. 17,2000 Model: N104S1-01
Tentative
6. MECHANICAL DRAWING
Please refer to the attached drawings.
7. PRECAUTION 7. 1 ASSEMBLY AND HANDLING PRECAUTION
(1) (2) Do not apply rough force such as bending or twisting to the module during assembly. To assemble or install module into user's system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It's not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged. (4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD module when it is operating. (9) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. (10)When ambient temperature is lower than 10C may reduce the display quality. For example, the response time will become slowly, and the starting voltage of CCFL will be higher than room temperature.
7.2 SAFETY PRECAUTION
(1) The start-up voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (3) After the module's end of life, it is not harmful in case of normal operation and storage.
17/19 This technical specification is tentative and it will be changed without notice. Please contact CMO 's representative while your product design is based on this specification. Version 0.1
CHI MEI
CHI MEI

▲Up To Search▲

Price & Availability of APAXT10C1

	To Download APAXT10C1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .